30 year on indigenous its invention, Rubik"s Cube

*
is still instantly recognizable. Human being like choose it up, turning it a few times, possibly doing a side or two (or five, together a braggart in my course once memorably claimed). Solving the cube remains a fairly rare feat - you"re either smart enough to have actually figured it out yourself, or geeky enough to have followed a how-to, and also most people are neither. Rubik"s cube is not just the quintessential hand-held puzzle, though: it"s likewise an iconic piece of design, so ns co-opted it as soon as making a brand-new chest of drawers because that my son"s room. This cubic piece of furniture has actually only one of the three compelled axes that rotation, therefore is unsolvable in the typical sense, yet can be arranged in any type of configuration you like by non-sporting means. The drawers do pose a brain-bending challenge: the first thing you need to solve is detecting the they"re there, and also all three have actually hidden locks in different locations.

You are watching: Rubik's cube table


*
three pairs the 22" full extension slides
*
shorter screws than those detailed with the above, speak 60 1/2" level head screws 36 3/8" rare-earth magnets
*
(in hindsight, the 9 top top the optimal are no really necessary, so 36 would certainly be enough) 54 3/8" stole washers (note over there is naught special around the 3/8" - use whatever thin magnet/washer combo is convenient) 54 6 mm x 30 mm dowels, reduced in fifty percent Wood glue Epoxy adhesive Brad nails Undercoat Gloss repaint in six different colors of your choice. I supplied spraypaint, together it"s a relatively cheap method of getting small quantities of paint, they save well, and they"re handy to have actually around. Black color gloss paint Close to $200 every up.Tools: one saw, table saw, miter saw, router, orbital sander, cordless drill through a 3/8" forstner bit
*
, and also a brad nailer.


||||

Cut the plywood right into the following dimensions. You"ll an alert that my extra fifty percent sheet the 1/2" ply actually come from offcuts I had lying about from various other projects (yes, also after do the Lego building and construction table, ns still had actually a few old cabinet doors left over...).1/2" plywood (11 mm thick) 6 that 600 x 582 mm (tops and bottoms the cases) 6 that 582 x 178 mm (sides that cases) 3 that 600 x 200 mm (drawer fronts) 6 that 543 x 160 mm (sides the drawers)1/4" plywood (7 mm thick) 3 of 600 x 200 mm (backs of cases) 3 that 550 x 550 mm (bottoms that drawers) 3 the 550 x 160 mm (backs the drawers) 54 the 165 x 165 mm (the "stickers", see later for much more detailed instruction on these) I constantly cut making use of a straightedge with the one saw, which offers you a perfect straight line but requires a couple of clamps. Gain a kind finishing blade, you"ll save yourself a most sanding. I usage Freud thin-kerf chisels in all my saws - the top quality is excellent, and also it to reduce the pack on the saw and the lot of sawdust produced. I provided the bench saw and miter experienced wherever possible, due to the fact that the set-up is quicker. Reduced to a stop using the miter observed to ensure reproducibility.


|||

These are ideal attached prior to you rally the individual cases. The exact height doesn"t yes, really matter, however make sure they"re square, parallel to each other, and also 5 mm back from the front edge.


|||||||||

Assemble the situations with hardwood glue and also brad nails, as shown. Leave to dry overnight, climate sand, fill any imperfections through wood filler, and also sand again.


Build three an ext boxes, without a top or front, the fit nicely inside the runners. Ns made the base and back with 1/4" ply and the sides through 1/2" ply. Nailing right into the leaf of 1/4" ply is perfect doable, however you do need to be a fair bit an ext precise than for 1/2". Sand and fill.


Attach the drawers come the slides, and also check the fit (whether they on slide in and also out nicely). Placed the instance on end, and also drop other in behind the drawer so it will certainly sit contempt proud as soon as closed. Heat up her drawer front, and also mark and cut to fit. Glue and nail to the drawer, again taking care with the nailing (I recommend delivering the lines to the front to stop errors). Round the edges of the drawer front to enhance the case, eliminate the stop, and also sand, fill and also sand again.


To develop the illusion that the cube deserve to spin conventionally (i.e. On three axes, not simply one), ns faked it making use of a router v a V-shaped little bit to reduced grooves in all the exposed faces. Use a guide - due to the fact that it"s hard to clamp on come a face, I simply tacked the guide in location temporarily making use of the brad nailer the correct street from the desired groove. I ripped a item of wood specifically the ideal width so I might rout both sides using the same guide (with my router, it essential to be 56 mm). The groove doesn"t look specifically like the horizontal gaps, the course, however the intuitive illusion hold at the very least at an initial glance.


I measured each cubie to be 19.1 mm top top a side, and each sticker together 15.6 mm, about 81% of the size. So i rounded as much as the nearest 5 mm (165 mm for a "sticker" for a 200 mm cubie) and also ripped much of one sheet of 1/4" plywood into 170 mm strips. I then set a protect against on my miter observed to 165 mm and made 2 cuts for every square, to ensure the 54 squares were together close to perfect together possible. I ganged them all in addition to a strap, and routed and also sanded the corners of every squares simultaneously. This action was nice quick, and all the components were done now. Just painting and also hardware to go!


Remove the drawers, and also take the hardware turn off them. Undercoat whatever except the within of the instances (you don"t view them), then sand. Paint the cases and drawer fronts gloss black to offer it a glowing plastic look. 3 coats have to do nicely, sanding lightly between coats with an extremely fine sandpaper.


Make a design template for this step. Drill 2 dowel-sized holes part way into every "sticker" (about 3/4 the method through), and also with the Forstner bit, drill a shallow (just deep enough for your washer) hole in the center. Repeat 54 times! friend really need two drills, or the swapping that bits will drive friend nuts. Now reduced 54 dowels in fifty percent by taping them come a scrap item of plywood and also running them with the bench saw. Glue the half-dowels into the holes. Epoxy the washers right into the shallow feet in the center.


Undercoat, then spray paint the edges and also top of every sticker in whatever mix of color you favor - we stuck to the conventional white/yellow/orange/red/green/blue. Ns let the future owner pick specifically which the shade of each he preferred of each. I spent a couple of minutes paint one coat, climate returned around 15 minutes later and also did another. I supplied about fifty percent a deserve to per collection of nine, i reckon.


You"ll need to use a design template again. Usage the previous theme to do this one; it demands to be 200 x 200 mm. Do the dowel feet slightly bigger (I used 15/64" because that the dowel holes, and also went come 17/64" because that these). Drill just deep sufficient for the magnet come sit flush through the surface ar (conveniently, this was just right into the second layer that ply, for this reason I just eyeballed it), but bore every the method through for the others. Repeat 45 times (you don"t have to do the base, for obvious reasons!). Glue the magnets in the holes using a slim layer of epoxy.


The 12" lazy Susan bearings are pretty low profile (9 mm), yet I decreased the gap between cases further by routing out a class of plywood native the situations (3 mm native each) to collection them into. I simply freehanded that after marking the present carefully. I greased the sphere bearings - this provides it stiffer but quieter, both desirable for this application. The lazy Susan bearing needs to be perfectly centered. Ns screwed one side on and just epoxied the other.


I added a straightforward hidden lock to each drawer, every in various places. I just drilled holes v case and drawer from the side, and also stuck a dowel in. Come unlock, you just remove the correct sticker and push in the dowel. It"s low tech however effective, and I don"t anticipate it spending lot time locked, yet it"s pretty to understand you can.


Add the "stickers" however you choose to get the style you desire (store the leftover nine stickers in among the drawers, that course!). Readjust the stickers and also make a new piece that furniture. Take it it because that a spin. Play some Scrabble (or 3D settlers of Catan). Leave it in the center of your living room together a coffee table. Lug it with you to a park and also confuse strangers. Organize your underwear in high geezer style. Talk to it. Sit ~ above it and slowly orbit. Placed your favorite boardgames in it. Challenge people to fix it one handed, and/or blindfolded, and also time them. Usage it together a was standing for your prize-winning laser-cut, LED-lit, Arduino-controlled, solar-powered, steampunk-themed, EL wire-crocheted Halloween cupcakes...

See more: Times Of You Wake Up And Time Has Slipped Away Lyrics, Times Of Your Life

Many many thanks to the following sites for featuring this build: make, boingboing, hackaday, neatorama, ohdeedoh, geekosystem, technabob, manmade, babble, wins.failblog, design-milk, storagegeek, discovery, thisiswhyimbroke and also others; thinkgeek for tweeting around it, and of course digitalrecordersreview.org individuals for every the good feedback. Cheers! Some human being have even made replicas! check out here, here and also here. If you do one, you re welcome send me a attach or article a picture in the comments.